Question
I am a novice when it comes to milling and post mill treatment, so please bear with me. I have a lot of SYP I have to remove from my property. This was cut abuot a year ago and has sat over a long dry summer in a pile of logs. I would really like to make use of the wood. I have a Lumbersmith Sawmill and have figured out the cutting pretty well and would now like to make something other than firewood. One of my goals is to make an old fashioned looking table similar to one in an old mill nearby. I want to use thick pieces of the pine and glue/biscuit them together to give a very solid heavy table for use in my shop. It will be about 14 feet long and I would like a bar at one end next to my fridge for the end of day refreshments.
I would like the top planks to be four inches thick and the bar to be eight inches. The legs would be probably four inches too, with open cabinets and slide out shelves. The wood is still pretty wet after sitting in log form for a year. I realize it is going to shrink some.
What would you recommend as the next steps from the freshly milled lumber? Air dry or build a kiln of some description? I have a lot more time than money, so lower cost solutions are preferred. If this comes out fairly well, I would like to take on more woodworking ventures. The finish pieces are going to be industrial grade and purposely dented, worn, and look like they have had 100 years of hard wear. I know the wood will probably continue to shrink post drying, and that is fine and will kind of work with the old fashioned, utilitarian look. Any cracks that form over time can be filled with epoxy. I just don't want it to fall apart.
Below is the result of playing with the mill and getting it set up and using a hefty patio to work under when the weather isn't great.
Forum Responses
(Sawing and Drying Forum)
From Gene Wengert, forum technical advisor:
Any idea what it will weigh? Is the floor strong enough? Can you tolerate warping too? This is a good idea if you can dry to 20% MC first.
The ways you're describing your end product don't seem very consistent to me. When I think industrial, utilitarian, I picture counter-bored lag bolts and gaps and cracks that are lived with, not biscuits, glued up slabs, and epoxy-filled imperfections. If you want to end up with a smooth, flat surface without gaps between boards then you'll need to start with thoroughly dry lumber, which isn't easy to achieve with the thicknesses you're going for. If you want it to look industrial, I suggest you build it the way it would be built in an industrial setting for industrial purposes - quick, solid, and simple.
Gene - I can throw a solar kiln together. Any recommendations on dry time? We are getting 60 degree days already down here. Would adding a basement dehumidifier in the kiln provide any further benefit?
Contributor A - there is some damage from the various critters for sure. As the piece is going to be intentionally faux aged, we can turn those into a feature of the aging. I have also cut down well into the heart wood too, and then treated with a combination of borate based poison (Penetreat Disodium Octaborate Tetrahydrate) mixed with propylene glycol antifreeze (basically emulating Boracare). I think the wood will be ok from a structure point of view.
Common Lumber Name | A | B | C |
Hardwoods | |||
Alder, Red | 9.9 | 19.2 | 2506 |
Apple | 10.9 | 31.7 | 4132 |
Ash, Black | 9.3 | 23.4 | 4132 |
Ash, Green | 14.3 | 27.6 | 3590 |
Aspen, Bigtooth | 10.3 | 18.7 | 2439 |
Aspen, Quaking | 10.3 | 18.2 | 2373 |
Basswood | 6.2 | 16.6 | 2174 |
Beech, American | 8.9 | 29.1 | 3793 |
Birch, Paper | 8.8 | 25.0 | 3260 |
Birch, Sweet | 11.9 | 31.2 | 4065 |
Birch, Yellow | 9.2 | 28.6 | 3723 |
Buckeye | 8.9 | 17.2 | 2235 |
Butternut | 11.3 | 18.7 | 2440 |
Cherry | 13.8 | 24.4 | 3184 |
Chesnut, American | 11.6 | 20.8 | 2708 |
Cottonwood | 8.5 | 16.1 | 2102 |
Dogwood | 6.8 | 33.3 | 4331 |
Elm, American | 10.2 | 23.9 | 3116 |
Elm, Rock | 12.2 | 29.6 | 3860 |
Elm, slippery | 11.5 | 25.0 | 3251 |
Hackberry | 11.8 | 25.5 | 3319 |
Hickory, Bitternut (Pecan) | 14.7 | 31.2 | 4062 |
Hickory (True) | |||
Hickory, Mockernut | 9.1 | 33.3 | 4332 |
Hickory, Pignut | 9.3 | 34.3 | 4332 |
Hickory, Shagbark | 10.9 | 33.3 | 4333 |
Hickory, Shellbark | 6.6 | 32.2 | 4195 |
Holly, American | 8.3 | 26.0 | 3387 |
Hophornbeam, Eastern | 7.9 | 32.8 | 4266 |
Laurel, California | 15.1 | 26.5 | 3456 |
Locust, Black | 21.2 | 34.3 | 4470 |
Madrone, Pacific | 7.8 | 30.2 | 3925 |
Maple (Soft) | |||
Maple, Bigleaf | 12.8 | 22.9 | 2980 |
Maple, Red | 13.1 | 25.5 | 3318 |
Maple, Silver | 12.4 | 22.9 | 2981 |
Maple (Hard) | |||
Maple, Black | 12.3 | 27.0 | 3523 |
Maple, Sugar | 12.3 | 29.1 | 3793 |
Oak (Red) | |||
Oak, Black | 11.7 | 29.1 | 3792 |
Oak, California black | 16.4 | 26.5 | 3455 |
Oak, Laurel | 6.3 | 29.1 | 3791 |
Oak, Northern red | 13.6 | 29.1 | 3793 |
Oak, Pin | 13.0 | 30.2 | 3928 |
Oak, Scarlet | 13.2 | 31.2 | 4065 |
Oak, Southern red | 9.6 | 27.0 | 3520 |
Oak, Water | 10.4 | 29.1 | 3793 |
Oak, Willow | 6.4 | 29.1 | 3790 |
Oak (White) | |||
Oak, Bur | 15.4 | 30.2 | 3928 |
Oak, Chestnut | 10.1 | 29.6 | 3858 |
Oak, Live | 17.5 | 41.6 | 5417 |
Oak, Overcup | 10.7 | 29.6 | 3860 |
Oak, Post | 11.0 | 31.2 | 4063 |
Oak, Swamp chestnut | 10.7 | 31.2 | 4063 |
Oak, White | 10.8 | 31.2 | 4062 |
Persimmon | 7.0 | 33.3 | 4332 |
Sweetgum | 8.9 | 23.9 | 3115 |
Sycamore | 10.7 | 23.9 | 3115 |
Tanoak | 9.0 | 30.2 | 3926 |
Tupelo, Black | 10.4 | 23.9 | 3116 |
Tupelo, Water | 12.4 | 23.9 | 3115 |
Walnut | 13.4 | 26.5 | 3454 |
Willow, Black | 8.6 | 18.7 | 2438 |
Yellow-poplar | 10.6 | 20.8 | 2708 |
Common Lumber Name | A | B | C |
Softwoods | |||
Baldcypress | 13.2 | 21.9 | 2844 |
Cedar, Alaska | 14.4 | 21.9 | 2844 |
Cedar, Atlantic white | 10.9 | 16.1 | 2100 |
Cedar, eastern red | 16.4 | 22.9 | 2981 |
Cedar, Incense | 13.1 | 18.2 | 2371 |
Cedar, Northern white | 11.1 | 15.1 | 1964 |
Cedar, Port-Orford | 12.6 | 20.2 | 2641 |
Cedar, Western red | 12.2 | 16.1 | 2100 |
Douglas-fir, Coast type | 12.3 | 23.4 | 3049 |
Douglas-fir, Interior west | 13.2 | 23.9 | 3116 |
Douglas-fir, Interior north | 14.0 | 23.4 | 3048 |
Fir, Balsam | 9.9 | 17.2 | 2236 |
Fir, California red | 10.6 | 18.7 | 2437 |
Fir, Grand | 10.7 | 18.2 | 2371 |
Fir, Noble | 10.1 | 19.2 | 2507 |
Fir, Pacific silver | 10.4 | 20.8 | 2711 |
Fir, Subalpine | 10.5 | 16.1 | 2101 |
Fir, White | 12.2 | 19.2 | 2506 |
Hemlock, Eastern | 12.6 | 19.8 | 2573 |
Hemlock, Western | 11.5 | 21.8 | 2847 |
Larch, Western | 11.3 | 25.0 | 3251 |
Pine, Eastern white | 12.3 | 17.7 | 2303 |
Pine, Lodgepole | 11.5 | 19.8 | 2576 |
Pine, Ponderosa | 12.6 | 19.8 | 2573 |
Pine, Red | 12.2 | 21.3 | 2777 |
Southern yellow group | |||
Pine, Loblolly | 12.9 | 24.4 | 3183 |
Pine, Longleaf | 15.0 | 28.1 | 3658 |
Pine, Shortleaf | 12.9 | 24.4 | 3183 |
Pine, Sugar | 12.6 | 17.7 | 2302 |
Pine, Western white | 10.0 | 18.2 | 2370 |
Redwood, Old growth | 14.9 | 19.8 | 2573 |
Redwood, Second growth | 13.2 | 17.7 | 2302 |
Spruce, Black | 11.3 | 19.8 | 2575 |
Spruce, Engelmann | 10.0 | 17.2 | 2234 |
Spruce, Red | 10.6 | 19.2 | 2506 |
Spruce, Sitka | 10.8 | 19.2 | 2506 |
Tamarack | 12.0 | 25.5 | 3318 |